View MLF2012C100KT000_8459371.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

inductors march 2015 multilayer ferrite mlf2012 2012 [0805 inch]* * dimensions code jis[eia] inductors for standard circuits mlf2012 ty p e mlf series
(2/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. inductors for standard circuits multilayer ferrite features the lineup includes a wide inductance range. highly reliable monolithic structure with multilayer integration. application smart phones, tablet termi nals, tuners, lcd-tvs, pdp-tv s, audio equipment, computer s, signal processing for modules etc. part number construction operating temperature range, pack age quantity, product weight in case the product's inductance is 15h or higher, both operating and storage temperature ranges are C40 to +85c. the storage temperature range is for after the circuit board is mounted. product compatible with rohs directive halogen-free compatible with lead-free solders overview of mlf2012 type mlf 2012 d 47n t000 series name lwh dimensions characteristics inductance inductance tolerance packaging style internal code (mm) (h) 2012 2.01.250.85 a 10n 0.010 (10nh) j 5% t taping 000 2.01.251.25 c k 10% d r10 0.1 m 20% e1r0 1 k 100 10 type temperature range package quantity individual weight operating temperature c storage temperature c (pieces/reel) mg mlf2012 t=0.85 C55 to +125 C55 to +125 4,000 10 t=1.25 2,000 14 rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlf2012 type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 30 to 60s 250 to 260c 10s max. natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlf2012 type shape & dimensions recommended land pattern dimensions in mm t 0.850.20 1.250.20 2.000.20 t 1.250.20 0.500.30 0.500.30 dimensions in mm 1.2 0.8 1.0 0.8
(6/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlf2012 type electrical characteristics characteristics specification table the " " of the part number contains the inductance tolerance code, j (5%), k (10%), or m (20%). measurement equipment ? equivalent measurement equipment may be used. l q l, q measuring conditions self-resonant frequency dc resistance rated current thickness part no. frequency current t (h) tolerance min. typ. (mhz) (ma) (mhz) min. (mhz) typ. ( ) max. ( ) typ. (ma) max. (mm) 0.047 20% 15 25 50 1.0 550 700 0.10 0.05 300 0.85 mlf2012d47n t000 0.068 20% 15 25 50 1.0 500 600 0.15 0.08 300 0.85 mlf2012d68n t000 0.082 20% 15 25 50 1.0 450 550 0.15 0.08 300 0.85 mlf2012d82n t000 0.10 5%10%20% 20 30 25 1.0 400 500 0.15 0.10 300 0.85 mlf2012dr10 t000 0.12 5%10%20% 20 30 25 1.0 360 450 0.20 0.12 300 0.85 mlf2012dr12 t000 0.15 5%10%20% 20 30 25 1.0 320 410 0.20 0.13 300 0.85 mlf2012dr15 t000 0.18 5%10%20% 20 30 25 1.0 280 370 0.25 0.15 300 0.85 mlf2012dr18 t000 0.22 5%10%20% 20 30 25 1.0 250 330 0.30 0.16 250 0.85 mlf2012dr22 t000 0.27 5%10%20% 20 30 25 1.0 220 300 0.35 0.18 250 0.85 mlf2012dr27 t000 0.33 5%10%20% 20 30 25 1.0 200 270 0.40 0.23 250 0.85 mlf2012dr33 t000 0.39 5%10%20% 25 35 25 1.0 180 250 0.45 0.25 200 0.85 mlf2012dr39 t000 0.47 5%10%20% 25 35 25 1.0 160 230 0.50 0.25 200 1.25 mlf2012dr47 t000 0.56 5%10%20% 25 35 25 1.0 150 210 0.55 0.30 150 1.25 mlf2012dr56 t000 0.68 5%10%20% 25 35 25 1.0 140 190 0.60 0.35 150 1.25 mlf2012dr68 t000 0.82 5%10%20% 25 35 25 1.0 130 170 0.65 0.40 150 1.25 mlf2012dr82 t000 1.0 5%10%20% 45 55 10 1.0 120 160 0.30 0.15 80 0.85 mlf2012a1r0 t000 1.2 5%10%20% 45 55 10 1.0 110 150 0.35 0.15 80 0.85 mlf2012a1r2 t000 1.5 5%10%20% 45 60 10 1.0 100 140 0.40 0.18 80 0.85 mlf2012a1r5 t000 1.8 5%10%20% 45 60 10 1.0 90 130 0.45 0.20 80 0.85 mlf2012a1r8 t000 2.2 5%10%20% 45 60 10 1.0 80 120 0.50 0.22 50 0.85 mlf2012a2r2 t000 2.7 5%10%20% 45 70 10 1.0 70 100 0.55 0.25 50 1.25 mlf2012a2r7 t000 3.3 5%10%20% 45 70 10 1.0 60 90 0.60 0.28 50 1.25 mlf2012a3r3 t000 3.9 5%10%20% 45 70 10 1.0 55 80 0.65 0.30 30 1.25 mlf2012a3r9 t000 4.7 5%10%20% 45 70 10 1.0 50 70 0.70 0.35 30 1.25 mlf2012a4r7 t000 5.6 5%10%20% 50 75 4 0.1 45 65 0.60 0.30 15 1.25 mlf2012e5r6 t000 6.8 5%10%20% 50 75 4 0.1 40 60 0.65 0.32 15 1.25 mlf2012e6r8 t000 8.2 5%10%20% 50 75 4 0.1 35 55 0.70 0.35 15 1.25 mlf2012e8r2 t000 10 5%10%20% 50 75 2 0.1 30 50 0.80 0.40 15 1.25 mlf2012e100 t000 12 5%10%20% 50 75 2 0.1 25 45 0.90 0.50 15 1.25 mlf2012e120 t000 15 10%20% 30 45 1 0.1 22 40 0.70 0.35 5 1.25 mlf2012c150 t000 18 10%20% 30 45 1 0.1 20 38 0.80 0.38 5 1.25 mlf2012c180 t000 22 10%20% 30 45 1 0.1 18 35 0.90 0.45 5 1.25 mlf2012c220 t000 27 10%20% 30 45 1 0.1 17 33 1.00 0.50 5 1.25 mlf2012c270 t000 33 10%20% 30 45 0.4 0.1 15 28 1.10 0.55 5 1.25 mlf2012c330 t000 39 10%20% 35 55 2 0.1 13 23 2.40 1.30 4 1.25 mlf2012k390 t000 47 10%20% 35 55 2 0.1 11 20 2.70 1.60 4 1.25 mlf2012k470 t000 56 10%20% 35 55 2 0.1 10 18 2.80 1.80 4 1.25 mlf2012k560 t000 68 10%20% 25 45 1 0.1 9 16 2.90 2.00 2 1.25 mlf2012c680 t000 82 10%20% 25 45 1 0.1 8 14 3.00 2.40 2 1.25 mlf2012c820 t000 100 10%20% 25 45 1 0.1 7 12 3.10 2.50 2 1.25 mlf2012c101 t000 measurement item product no. manufacturer l, q 4294a+16034g agilent technologies self-resonant frequency e4991a agilent technologies dc resistance type-7561 yokogawa
(7/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlf2012 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 1 10 100 1000 0.01 100 10 1 0.1 frequency ( mhz ) inductance ( h ) e100 dr68 dr47 dr33 dr22 dr15 dr10 e6r8 a4r7 a3r3 a2r2 a1r5 a1r0 1 10 100 1000 0.01 100 10 1 0.1 frequency ( mhz ) inductance ( h ) e120 e8r2 e5r6 a3r9 a2r7 a1r8 dr82 dr56 dr39 dr27 dr18 dr12 a1r2 product no. manufacturer e4991a+16192a agilent technologies
(8/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlf2012 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.1 10 1 100 0.1 100 10 1 frequency ( mhz ) inductance ( h ) c101 c820 k560 k470 k390 c270 c220 c180 c150 c680 c330 product no. manufacturer 4294a+16034g agilent technologies
(9/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlf2012 type electrical characteristics q frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0 10 20 30 40 50 90 70 80 60 q 11 0 1000 100 frequency ( mhz ) e100 e6r8 a1r0 dr33 dr15 dr10 a3r3 a2r2 a1r5 dr47 dr22 dr68 a4r7 0 10 20 30 40 50 90 80 70 60 q 11 0 1000 100 frequency ( mhz ) e120 e8r2 e5r6 a3r9 a2r7 a1r8 dr82 dr56 dr39 dr27 dr18 dr12 a1r2 product no. manufacturer e4991a+16192a agilent technologies
(10/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlf2012 type q frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0 10 20 30 40 50 90 80 70 60 q 0.1 10 100 1 frequency ( mhz ) c101 c820 c680 k560 k470 k390 c330 c270 c220 c180 c150 product no. manufacturer 4294a+16034g agilent technologies
(11/11) inductors 20150310 / inductor_commercial_standard_mlf2012_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. mlf2012 type packaging style reel dimensions tape dimensions 1.0 ?180 2.0 2.0 0.5 ?13 0.2 ?21 0.8 ?60min. 14.4max. dimensions in mm 8.4 +2.0 C0.0 8.00.3 3.50.05 1.750.1 4.0 0.1 1.5 +0.1 C0.0 sprocket hole cavity a kb 2.0 0.05 2.0 0.05 160min. taping 200min. 300min. drawing direction dimensions in mm ty p e a b k mlf2012 t=0.85 2.30.2 1.50.2 1.1 max. t=1.25 2.30.2 1.50.2 1.5 max.

▲Up To Search▲

Price & Availability of MLF2012C100KT000

	To Download MLF2012C100KT000 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .